You are here: irt.org | RFCs | RFC2011 [ previous next ]
Network Working Group K. McCloghrie, Editor Request for Comments: 2011 Cisco Systems Updates: 1213 November 1996 Category: Standards Track SNMPv2 Management Information Base for the Internet Protocol using SMIv2 Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. IESG Note: The IP, UDP, and TCP MIB modules currently support only IPv4. These three modules use the IpAddress type defined as an OCTET STRING of length 4 to represent the IPv4 32-bit internet addresses. (See RFC 1902, SMI for SNMPv2.) They do not support the new 128-bit IPv6 internet addresses. Table of Contents 1. Introduction ............................................... 1 2. Definitions ................................................ 2 2.1 The IP Group .............................................. 3 2.2 The ICMP Group............................................. 11 2.3 Conformance Information ................................... 16 2.3.1 Compliance Statements ................................... 16 2.3.2 Units of Conformance .................................... 16 3. Acknowledgements ........................................... 18 4. References ................................................. 18 5. Security Considerations .................................... 18 6. Editor's Address ........................................... 18 1. Introduction A management system contains: several (potentially many) nodes, each with a processing entity, termed an agent, which has access to management instrumentation; at least one management station; and, a management protocol, used to convey management information between the agents and management stations. Operations of the protocol are carried out under an administrative framework which defines authentication, authorization, access control, and privacy policies. McCloghrie Standards Track [Page 1]
RFC 2011 SNMPv2 MIB for IP November 1996 Management stations execute management applications which monitor and control managed elements. Managed elements are devices such as hosts, routers, terminal servers, etc., which are monitored and controlled via access to their management information. Management information is viewed as a collection of managed objects, residing in a virtual information store, termed the Management Information Base (MIB). Collections of related objects are defined in MIB modules. These modules are written using a subset of OSI's Abstract Syntax Notation One (ASN.1) [1], termed the Structure of Management Information (SMI) [2]. This document is the MIB module which defines managed objects for managing implementations of the Internet Protocol (IP) [3] and its associated Internet Control Message Protocol (ICMP) [4]. The managed objects in this MIB module were originally defined using the SNMPv1 framework as a part of MIB-II [5]. Since then, the managed objects related to managing routes in an IP internet were updated by RFC 1354 [6]. This document takes the remaining MIB-II objects for these protocols, and defines them using the SNMPv2 framework. 2. Definitions IP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, IpAddress, mib-2 FROM SNMPv2-SMI PhysAddress FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; ipMIB MODULE-IDENTITY LAST-UPDATED "9411010000Z" ORGANIZATION "IETF SNMPv2 Working Group" CONTACT-INFO " Keith McCloghrie Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 US Phone: +1 408 526 5260 Email: kzm@cisco.com" McCloghrie Standards Track [Page 2]
RFC 2011 SNMPv2 MIB for IP November 1996 DESCRIPTION "The MIB module for managing IP and ICMP implementations, but excluding their management of IP routes." REVISION "9103310000Z" DESCRIPTION "The initial revision of this MIB module was part of MIB- II." ::= { mib-2 48} -- the IP group ip OBJECT IDENTIFIER ::= { mib-2 4 } ipForwarding OBJECT-TYPE SYNTAX INTEGER { forwarding(1), -- acting as a router notForwarding(2) -- NOT acting as a router } MAX-ACCESS read-write STATUS current DESCRIPTION "The indication of whether this entity is acting as an IP router in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP routers forward datagrams. IP hosts do not (except those source-routed via the host)." ::= { ip 1 } ipDefaultTTL OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol." ::= { ip 2 } ipInReceives OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of input datagrams received from interfaces, including those received in error." ::= { ip 3 } McCloghrie Standards Track [Page 3]
RFC 2011 SNMPv2 MIB for IP November 1996 ipInHdrErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc." ::= { ip 4 } ipInAddrErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP routers and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address." ::= { ip 5 } ipForwDatagrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP routers, this counter will include only those packets which were Source-Routed via this entity, and the Source-Route option processing was successful." ::= { ip 6 } ipInUnknownProtos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol." McCloghrie Standards Track [Page 4]
RFC 2011 SNMPv2 MIB for IP November 1996 ::= { ip 7 } ipInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly." ::= { ip 8 } ipInDelivers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of input datagrams successfully delivered to IP user-protocols (including ICMP)." ::= { ip 9 } ipOutRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IP datagrams which local IP user- protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams." ::= { ip 10 } ipOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion." ::= { ip 11 } ipOutNoRoutes OBJECT-TYPE McCloghrie Standards Track [Page 5]
RFC 2011 SNMPv2 MIB for IP November 1996 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagrams which a host cannot route because all of its default routers are down." ::= { ip 12 } ipReasmTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity." ::= { ip 13 } ipReasmReqds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP fragments received which needed to be reassembled at this entity." ::= { ip 14 } ipReasmOKs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP datagrams successfully re-assembled." ::= { ip 15 } ipReasmFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failures detected by the IP re-assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by McCloghrie Standards Track [Page 6]
RFC 2011 SNMPv2 MIB for IP November 1996 combining them as they are received." ::= { ip 16 } ipFragOKs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP datagrams that have been successfully fragmented at this entity." ::= { ip 17 } ipFragFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set." ::= { ip 18 } ipFragCreates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IP datagram fragments that have been generated as a result of fragmentation at this entity." ::= { ip 19 } -- the IP address table ipAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of addressing information relevant to this entity's IP addresses." ::= { ip 20 } ipAddrEntry OBJECT-TYPE SYNTAX IpAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The addressing information for one of this entity's IP McCloghrie Standards Track [Page 7]
RFC 2011 SNMPv2 MIB for IP November 1996 addresses." INDEX { ipAdEntAddr } ::= { ipAddrTable 1 } IpAddrEntry ::= SEQUENCE { ipAdEntAddr IpAddress, ipAdEntIfIndex INTEGER, ipAdEntNetMask IpAddress, ipAdEntBcastAddr INTEGER, ipAdEntReasmMaxSize INTEGER } ipAdEntAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address to which this entry's addressing information pertains." ::= { ipAddrEntry 1 } ipAdEntIfIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex." ::= { ipAddrEntry 2 } ipAdEntNetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0." ::= { ipAddrEntry 3 } ipAdEntBcastAddr OBJECT-TYPE SYNTAX INTEGER (0..1) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the least-significant bit in the IP broadcast McCloghrie Standards Track [Page 8]
RFC 2011 SNMPv2 MIB for IP November 1996 address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface." ::= { ipAddrEntry 4 } ipAdEntReasmMaxSize OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface." ::= { ipAddrEntry 5 } -- ipRouteTable ::= { ip 21 } obsolete -- the IP Address Translation table -- The Address Translation tables contain the IpAddress to -- "physical" address equivalences. Some interfaces do not -- use translation tables for determining address -- equivalences (e.g., DDN-X.25 has an algorithmic method); -- if all interfaces are of this type, then the Address -- Translation table is empty, i.e., has zero entries. ipNetToMediaTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNetToMediaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP Address Translation table used for mapping from IP addresses to physical addresses." ::= { ip 22 } ipNetToMediaEntry OBJECT-TYPE SYNTAX IpNetToMediaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains one IpAddress to `physical' address equivalence." INDEX { ipNetToMediaIfIndex, ipNetToMediaNetAddress } McCloghrie Standards Track [Page 9]
RFC 2011 SNMPv2 MIB for IP November 1996 ::= { ipNetToMediaTable 1 } IpNetToMediaEntry ::= SEQUENCE { ipNetToMediaIfIndex INTEGER, ipNetToMediaPhysAddress PhysAddress, ipNetToMediaNetAddress IpAddress, ipNetToMediaType INTEGER } ipNetToMediaIfIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex." ::= { ipNetToMediaEntry 1 } ipNetToMediaPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The media-dependent `physical' address." ::= { ipNetToMediaEntry 2 } ipNetToMediaNetAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IpAddress corresponding to the media-dependent `physical' address." ::= { ipNetToMediaEntry 3 } ipNetToMediaType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following invalid(2), -- an invalidated mapping dynamic(3), static(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of mapping. McCloghrie Standards Track [Page 10]
RFC 2011 SNMPv2 MIB for IP November 1996 Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively disassociates the interface identified with said entry from the mapping identified with said entry. It is an implementation- specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object." ::= { ipNetToMediaEntry 4 } ipRoutingDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries." ::= { ip 23 } -- the ICMP group icmp OBJECT IDENTIFIER ::= { mib-2 5 } icmpInMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors." ::= { icmp 1 } icmpInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.)." ::= { icmp 2 } McCloghrie Standards Track [Page 11]
RFC 2011 SNMPv2 MIB for IP November 1996 icmpInDestUnreachs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Destination Unreachable messages received." ::= { icmp 3 } icmpInTimeExcds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Time Exceeded messages received." ::= { icmp 4 } icmpInParmProbs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Parameter Problem messages received." ::= { icmp 5 } icmpInSrcQuenchs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Source Quench messages received." ::= { icmp 6 } icmpInRedirects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Redirect messages received." ::= { icmp 7 } icmpInEchos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo (request) messages received." ::= { icmp 8 } McCloghrie Standards Track [Page 12]
RFC 2011 SNMPv2 MIB for IP November 1996 icmpInEchoReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo Reply messages received." ::= { icmp 9 } icmpInTimestamps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Timestamp (request) messages received." ::= { icmp 10 } icmpInTimestampReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Timestamp Reply messages received." ::= { icmp 11 } icmpInAddrMasks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Address Mask Request messages received." ::= { icmp 12 } icmpInAddrMaskReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Address Mask Reply messages received." ::= { icmp 13 } icmpOutMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors." McCloghrie Standards Track [Page 13]
RFC 2011 SNMPv2 MIB for IP November 1996 ::= { icmp 14 } icmpOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value." ::= { icmp 15 } icmpOutDestUnreachs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Destination Unreachable messages sent." ::= { icmp 16 } icmpOutTimeExcds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Time Exceeded messages sent." ::= { icmp 17 } icmpOutParmProbs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Parameter Problem messages sent." ::= { icmp 18 } icmpOutSrcQuenchs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Source Quench messages sent." ::= { icmp 19 } McCloghrie Standards Track [Page 14]
RFC 2011 SNMPv2 MIB for IP November 1996 icmpOutRedirects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects." ::= { icmp 20 } icmpOutEchos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo (request) messages sent." ::= { icmp 21 } icmpOutEchoReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo Reply messages sent." ::= { icmp 22 } icmpOutTimestamps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Timestamp (request) messages sent." ::= { icmp 23 } icmpOutTimestampReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Timestamp Reply messages sent." ::= { icmp 24 } icmpOutAddrMasks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Address Mask Request messages sent." McCloghrie Standards Track [Page 15]
RFC 2011 SNMPv2 MIB for IP November 1996 ::= { icmp 25 } icmpOutAddrMaskReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Address Mask Reply messages sent." ::= { icmp 26 } -- conformance information ipMIBConformance OBJECT IDENTIFIER ::= { ipMIB 2 } ipMIBCompliances OBJECT IDENTIFIER ::= { ipMIBConformance 1 } ipMIBGroups OBJECT IDENTIFIER ::= { ipMIBConformance 2 } -- compliance statements ipMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMPv2 entities which implement IP." MODULE -- this module MANDATORY-GROUPS { ipGroup, icmpGroup } ::= { ipMIBCompliances 1 } -- units of conformance ipGroup OBJECT-GROUP OBJECTS { ipForwarding, ipDefaultTTL, ipInReceives, ipInHdrErrors, ipInAddrErrors, ipForwDatagrams, ipInUnknownProtos, ipInDiscards, ipInDelivers, ipOutRequests, ipOutDiscards, ipOutNoRoutes, ipReasmTimeout, ipReasmReqds, ipReasmOKs, ipReasmFails, ipFragOKs, ipFragFails, ipFragCreates, ipAdEntAddr, ipAdEntIfIndex, ipAdEntNetMask, ipAdEntBcastAddr, ipAdEntReasmMaxSize, ipNetToMediaIfIndex, ipNetToMediaPhysAddress, ipNetToMediaNetAddress, ipNetToMediaType, ipRoutingDiscards } STATUS current DESCRIPTION McCloghrie Standards Track [Page 16]
RFC 2011 SNMPv2 MIB for IP November 1996 "The ip group of objects providing for basic management of IP entities, exclusive of the management of IP routes." ::= { ipMIBGroups 1 } icmpGroup OBJECT-GROUP OBJECTS { icmpInMsgs, icmpInErrors, icmpInDestUnreachs, icmpInTimeExcds, icmpInParmProbs, icmpInSrcQuenchs, icmpInRedirects, icmpInEchos, icmpInEchoReps, icmpInTimestamps, icmpInTimestampReps, icmpInAddrMasks, icmpInAddrMaskReps, icmpOutMsgs, icmpOutErrors, icmpOutDestUnreachs, icmpOutTimeExcds, icmpOutParmProbs, icmpOutSrcQuenchs, icmpOutRedirects, icmpOutEchos, icmpOutEchoReps, icmpOutTimestamps, icmpOutTimestampReps, icmpOutAddrMasks, icmpOutAddrMaskReps } STATUS current DESCRIPTION "The icmp group of objects providing ICMP statistics." ::= { ipMIBGroups 2 } END McCloghrie Standards Track [Page 17]
RFC 2011 SNMPv2 MIB for IP November 1996 3. Acknowledgements This document contains a modified subset of RFC 1213. 4. References [1] Information processing systems - Open Systems Interconnection - Specification of Abstract Syntax Notation One (ASN.1), International Organization for Standardization. International Standard 8824, (December, 1987). [2] McCloghrie, K., Editor, "Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, Cisco Systems, January 1996. [3] Postel, J., "Internet Protocol - DARPA Internet Program Protocol Specification", STD 5, RFC 791, DARPA, September 1981. [4] Postel, J., "Internet Control Message Protocol - DARPA Internet Program Protocol Specification", STD 5, RFC 792, USC/Information Sciences Institute, September 1981. [5] McCloghrie, K., and M. Rose, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, March 1991. [6] Baker, F., "IP Forwarding Table MIB", RFC 1354, ACC, July 1992. 5. Security Considerations Security issues are not discussed in this memo. 6. Editor's Address Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 US Phone: +1 408 526 5260 EMail: kzm@cisco.com McCloghrie Standards Track [Page 18]