You are here: irt.org | RFCs | RFC6923 [ previous next ]
Internet Engineering Task Force (IETF) R. Winter Request for Comments: 6923 NEC Category: Standards Track E. Gray ISSN: 2070-1721 Ericsson H. van Helvoort Huawei Technologies Co., Ltd. M. Betts ZTE May 2013 MPLS Transport Profile (MPLS-TP) Identifiers Following ITU-T Conventions Abstract This document specifies an extension to the identifiers to be used in the Transport Profile of Multiprotocol Label Switching (MPLS-TP). Identifiers that follow IP/MPLS conventions have already been defined. This memo augments that set of identifiers for MPLS-TP management and Operations, Administration, and Maintenance (OAM) functions to include identifier information in a format typically used by the International Telecommunication Union Telecommunication Standardization Sector (ITU-T). Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6923. Winter, et al. Standards Track [Page 1]
RFC 6923 MPLS-TP ITU-T IDs May 2013 Copyright Notice Copyright (c) 2013 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction ....................................................2 1.1. Terminology ................................................3 1.2. Requirements Notation ......................................4 1.3. Notational Conventions .....................................4 2. Named Entities ..................................................4 3. Uniquely Identifying an Operator -- the ICC_Operator_ID .........5 3.1. Use of the ICC_Operator_ID .................................6 4. Node and Interface Identifiers ..................................7 5. MPLS-TP Tunnel and LSP Identifiers ..............................7 5.1. MPLS-TP Point-to-Point Tunnel Identifiers ..................7 5.2. MPLS-TP LSP Identifiers ....................................8 5.2.1. MPLS-TP Co-Routed Bidirectional LSP Identifiers .....8 5.2.2. MPLS-TP Associated Bidirectional LSP Identifiers ....9 6. Pseudowire Path Identifiers .....................................9 7. Maintenance Identifiers .........................................9 7.1. MEG Identifiers ...........................................10 7.2. MEP Identifiers ...........................................10 7.3. MIP Identifiers ...........................................10 8. Security Considerations ........................................11 9. References .....................................................11 9.1. Normative References ......................................11 9.2. Informative References ....................................12 1. Introduction This document augments the initial set of identifiers to be used in the Transport Profile of Multiprotocol Label Switching (MPLS-TP) defined in [RFC6370] by adding new identifiers based on ITU-T conventions. It is not intended that both types of identifiers will be used at the same time in the same domain. Winter, et al. Standards Track [Page 2]
RFC 6923 MPLS-TP ITU-T IDs May 2013 [RFC6370] defines a set of MPLS-TP transport and management entity identifiers to support bidirectional (co-routed and associated) point-to-point MPLS-TP Label Switched Paths (LSPs), including Pseudowires (PWs) and Sections that follow the IP/MPLS conventions. This document specifies an alternative way to generate unambiguous identifiers for operators/service providers based on ITU-T conventions and specifies how these operator/service provider identifiers can be used to generate unambiguous identifiers for the existing set of identifiable MPLS-TP entities described in [RFC6370]. This document solely defines those identifiers. Their use and possible protocol extensions to carry them are out of the scope of this document. In this document, we follow the notational convention laid out in [RFC6370], which is included in this document for convenience in Section 1.3. 1.1. Terminology CC: Country Code ICC: ITU Carrier Code ISO: International Organization for Standardization ITU: International Telecommunication Union ITU-T: ITU Telecommunication Standardization Sector LSP: Label Switched Path MEG: Maintenance Entity Group MEP: Maintenance Entity Group End Point MIP: Maintenance Entity Group Intermediate Point MPLS: Multiprotocol Label Switching PW: Pseudowire TSB: (ITU-T) Telecommunication Standardization Bureau UMC: Unique MEG ID Code Winter, et al. Standards Track [Page 3]
RFC 6923 MPLS-TP ITU-T IDs May 2013 1.2. Requirements Notation The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 1.3. Notational Conventions This document uses the notational conventions laid out in [RFC6370]: All multiple-word atomic identifiers use underscores (_) between the words to join the words. Many of the identifiers are composed of a set of other identifiers. These are expressed by listing the latter identifiers joined with double-colon "::" notation. Where the same identifier type is used multiple times in a concatenation, they are qualified by a prefix joined to the identifier by a dash (-). For example, A1-Node_ID is the Node_ID of a node referred to as A1. The notation defines a preferred ordering of the fields. Specifically, the designation A1 is used to indicate the lower sort order of a field or set of fields and Z9 is used to indicate the higher sort order of the same. The sort is either alphanumeric or numeric depending on the field's definition. Where the sort applies to a group of fields, those fields are grouped with {...}. Note, however, that the uniqueness of an identifier does not depend on the ordering, but rather, upon the uniqueness and scoping of the fields that compose the identifier. Further, the preferred ordering is not intended to constrain protocol designs by dictating a particular field sequence ... or even what fields appear in which objects. 2. Named Entities This document provides additional identifiers supplementing those defined in [RFC6370]. The identifiers in [RFC6370] are composed of a set of atomic identifiers, and this document defines some new atomic identifiers that can be substituted for some of those that have already been defined, to create new identifiers. The set of identifiers defined in [RFC6370] is: o Global_ID o Node Winter, et al. Standards Track [Page 4]
RFC 6923 MPLS-TP ITU-T IDs May 2013 o Interface o Tunnel o LSP o PW o MEG o MEP o MIP The following sections go through this list of identifiers one by one. The structure of this document is loosely aligned with the structure of [RFC6370]. 3. Uniquely Identifying an Operator -- the ICC_Operator_ID In [RFC6370], an operator is uniquely identified by the Global_ID, which is based on the Autonomous System (AS) number of the operator. The ITU-T, however, traditionally identifies operators and service providers based on the ITU Carrier Code (ICC) as specified in [M1400]. The ITU-T Telecommunication Standardization Bureau (TSB) maintains a list of assigned ICCs [ICC-list]. Note that ICCs, all of which are referenced at [ICC-list], can be assigned to ITU-T members as well as non-members. The national regulatory authorities act as an intermediary between the ITU/TSB and operators/service providers. One of the things that the national authorities are responsible for in the process of assigning an ICC is to ensure that the Carrier Codes are unique within their country. This uniqueness assumption is the basis for creating a globally unique ICC-based operator ID. The ICC itself is a string of one to six characters, each character being either alphabetic (i.e., A-Z) or numeric (i.e., 0-9). Alphabetic characters in the ICC SHOULD be represented with uppercase letters. Global uniqueness is assured by concatenating the ICC with a Country Code (CC). The Country Code (alpha-2) is a string of two alphabetic characters represented with uppercase letters (i.e., A-Z). Winter, et al. Standards Track [Page 5]
RFC 6923 MPLS-TP ITU-T IDs May 2013 The International Organization for Standardization (ISO) establishes internationally recognized codes for the representation of names of countries, territories or areas of geographical interest, and their subdivisions, published as a list of CCs [CC-list] in ISO Standard 3166-1 [ISO3166-1]. The ICC and CC characters are coded according to ITU-T Recommendation T.50 [T.50]. Together, the CC and the ICC form the ICC_Operator_ID as: CC::ICC 3.1. Use of the ICC_Operator_ID The ICC_Operator_ID is used as a replacement for the Global_ID as specified in [RFC6370], i.e., its purpose is to provide a globally unique context for other MPLS-TP identifiers. As an example, an Interface Identifier (IF_ID) in [RFC6370] is specified as the concatenation of the Node_ID (a unique 32-bit value assigned by the operator) and the Interface Number (IF_Num, a 32-bit unsigned integer assigned by the operator that is unique within the scope of a Node_ID). To make this IF_ID globally unique, the Global_ID is prefixed. This memo specifies the ICC_Operator_ID as an alternative format that, just like the Global_ID, is prefixed to the IF_ID. Using the notation from RFC 6370 [RFC6370]: Global_ID::Node_ID::IF_Num is functionally equivalent to: ICC_Operator_ID::Node_ID::IF_Num The same substitution procedure applies to all identifiers specified in [RFC6370] with the exception of the MEG ID, MEP ID, and MIP ID. MEG, MEP, and MIP Identifiers are redefined in this document (see Sections 7.1, 7.2, and 7.3, respectively). Winter, et al. Standards Track [Page 6]
RFC 6923 MPLS-TP ITU-T IDs May 2013 4. Node and Interface Identifiers The format of the Node and Interface Identifiers are not changed by this memo except for the case when global uniqueness is required. [RFC6370] defines the Node Identifier (Node_ID) as a unique 32-bit value assigned by the operator within the scope of a Global_ID. The structure of the Node_ID itself is not defined as it is left to the operator to choose an appropriate value. The value zero, however, is reserved and MUST NOT be used. This document does not change the above definition. However, in case global uniqueness is required, the Node_ID is prefixed with the ICC_Operator_ID as defined in Section 3. [RFC6370] further defines interface numbers (IF_Num) as 32-bit unsigned integers that can be freely assigned by the operator and must be unique in the scope of the respective Node_ID. The IF_Num value 0 has a special meaning, and therefore, it MUST NOT be used to identify an MPLS-TP interface. An Interface Identifier (IF_ID) identifies an interface uniquely within the context of an ICC_Operator_ID. It is formed by concatenating the Node_ID with the IF_Num to result in a 64-bit identifier formed as Node_ID::IF_Num. Global uniqueness of the IF_ID, if needed, can be assured by prefixing the identifier with the ICC_Operator_ID. 5. MPLS-TP Tunnel and LSP Identifiers This document does not change the definition for local Tunnel and LSP IDs. When global uniqueness is needed, the format of these identifiers is as described in Sections 5.1 and 5.2. 5.1. MPLS-TP Point-to-Point Tunnel Identifiers Tunnel IDs (Tunnel_ID) are based on the end points' Node_IDs and locally assigned tunnel numbers (Tunnel_Num), which identify the tunnel at each end point. The tunnel number is a 16-bit unsigned integer unique within the context of the Node_ID. A full Tunnel ID is represented by the concatenation of these two end-point-specific identifiers. Using the A1/Z9 convention, the format of a Tunnel_ID is: A1-{Node_ID::Tunnel_Num}::Z9-{Node_ID::Tunnel_Num} Winter, et al. Standards Track [Page 7]
RFC 6923 MPLS-TP ITU-T IDs May 2013 Where global uniqueness is required, using ITU-T conventions, the ICC_Operator_ID is prefixed to the Tunnel_ID. Thus, a globally unique Tunnel_ID becomes: A1-{ICC_Operator_ID::Node_ID::Tunnel_Num}:: Z9-{ICC_Operator_ID::Node_ID::Tunnel_Num} As per [RFC6370], when an MPLS-TP tunnel is configured, it MUST be assigned a unique IF_ID at each end point as defined in Section 4. 5.2. MPLS-TP LSP Identifiers The following subsections define identifiers for MPLS-TP co-routed bidirectional and associated bidirectional LSPs. Since MPLS-TP Sub-Path Maintenance Entities (SPMEs) are also LSPs, they use the same form of IDs. 5.2.1. MPLS-TP Co-Routed Bidirectional LSP Identifiers The LSP Identifier (LSP_ID) for a co-routed bidirectional LSP is formed by adding a 16-bit unsigned integer LSP number (LSP_Num) to the Tunnel ID. Consequently, the format of an MPLS-TP co-routed bidirectional LSP_ID is: A1-{Node_ID::Tunnel_Num}::Z9-{Node_ID::Tunnel_Num}::LSP_Num [RFC6370] notes that the "uniqueness of identifiers does not depend on the A1/Z9 sort ordering". A co-routed bidirectional LSP is provisioned or signaled as a single entity, and therefore, a single LSP_Num is used for both unidirectional LSPs. These can be referenced by the following identifiers: A1-Node_ID::A1-Tunnel_Num::LSP_Num::Z9-Node_ID and Z9-Node_ID::Z9-Tunnel_Num::LSP_Num::A1-Node_ID, respectively. Global uniqueness is accomplished by using globally unique Node_IDs. A globally unique LSP_ID consequently becomes: A1-{ICC_Operator_ID::Node_ID::Tunnel_Num}:: Z9-{ICC_Operator_ID::Node_ID::Tunnel_Num}::LSP_Num Winter, et al. Standards Track [Page 8]
RFC 6923 MPLS-TP ITU-T IDs May 2013 5.2.2. MPLS-TP Associated Bidirectional LSP Identifiers An associated bidirectional LSP needs a separate LSP_Num for both of its unidirectional LSPs. The LSP number is again a 16-bit unsigned integer that needs to be unique within the scope of the ingress's Tunnel_Num. Consequently, the format of an MPLS-TP associated bidirectional LSP_ID is: A1-{Node_ID::Tunnel_Num::LSP_Num}:: Z9-{Node_ID::Tunnel_Num::LSP_Num} Each of the unidirectional LSPs of which the associated bidirectional LSP is composed may be referenced by one of the following identifiers: A1-Node_ID::A1-Tunnel_Num::A1-LSP_Num::Z9-Node_ID and Z9-Node_ID::Z9-Tunnel_Num::Z9-LSP_Num::A1-Node_ID, respectively. A globally unique LSP_ID is constructed using the globally unique Node_IDs as defined before. Consequently, a globally unique LSP_ID is formulated as: A1-{ICC_Operator_ID::Node_ID::Tunnel_Num::LSP_Num}:: Z9-{ICC_Operator_ID::Node_ID::Tunnel_Num::LSP_Num} 6. Pseudowire Path Identifiers The PW Path Identifier (PW_Path_ID) is structured in a similar manner as the PW_Path_ID described in Section 6 of [RFC6370]. Instead of the Global_ID used in [RFC6370], this document uses the ICC_Operator_ID to make the PW_Path_ID globally unique. In this document, the Attachment Individual Identifier (AII) is composed of three fields. These are the ICC_Operator_ID, the Node_ID, and the AC_ID. The AC_ID is as defined in [RFC5003]. The complete globally unique PW_Path_ID is formulated as: A1-{ICC_Operator_ID::Node_ID::AC_ID}:: Z9-{ICC_Operator_ID::Node_ID::AC_ID} 7. Maintenance Identifiers The following subsections define the identifiers for the various maintenance-related groups and entities as defined in [RFC6371]. In contrast to the IDs defined in [RFC6370], this document does not define separate maintenance identifiers for Sections, PWs, and LSPs. Winter, et al. Standards Track [Page 9]
RFC 6923 MPLS-TP ITU-T IDs May 2013 7.1. MEG Identifiers MEG_IDs for MPLS-TP Sections, LSPs, and PWs following ITU-T conventions are based on the globally unique ICC_Operator_ID. In this case, the MEG_ID is a string of up to 15 characters and consists of three subfields: the Country Code (as described in Section 3) and the ICC (as described in Section 3) -- which together form the ICC_Operator_ID -- followed by a Unique MEG ID Code (UMC) as defined in [Y.1731_cor1]. The resulting MEG_ID is: CC::ICC::UMC To avoid the potential for the concatenation of a short (i.e., less than 6 characters) ICC with a UMC not being unique, the UMC MUST start with the "/" character, which is not allowed in the ICC itself. This way, the MEG_ID can also be easily decomposed into its individual components by a receiver. The UMC MUST be unique within the organization identified by the combination of CC and ICC. The ICC_Operator_ID-based MEG_ID may be applied equally to a single MPLS-TP Section, LSP, or Pseudowire. 7.2. MEP Identifiers ICC_Operator_ID-based MEP_IDs for MPLS-TP Sections, LSPs, and Pseudowires are formed by appending a 16-bit index to the MEG_ID defined in Section 7.1. Within the context of a particular MEG, we call the identifier associated with a MEP the MEP Index (MEP_Index). The MEP_Index is administratively assigned. It is encoded as a 16-bit unsigned integer and MUST be unique within the MEG. An ICC_Operator_ID-based MEP_ID is structured as: MEG_ID::MEP_Index An ICC_Operator_ID-based MEP ID is globally unique by construction given the ICC_Operator_ID-based MEG_ID's global uniqueness. 7.3. MIP Identifiers ICC_Operator_ID-based MIP_IDs for MPLS-TP Sections, LSPs, and Pseudowires are formed by a global IF_ID that is obtained by prefixing the identifier of the interface on which the MIP resides Winter, et al. Standards Track [Page 10]
RFC 6923 MPLS-TP ITU-T IDs May 2013 with the ICC_Operator_ID as described in Section 3.1. This allows MIPs to be independently identified in nodes where a per-interface MIP model is used. If only a per-node MIP model is used, one MIP is configured. In this case, the MIP_ID is formed by using the Node_ID and an IF_Num of 0. 8. Security Considerations This document extends an existing naming scheme and does not introduce new security concerns. However, as mentioned in the Security Considerations section of [RFC6370], protocol specifications that describe the use of this naming scheme may introduce security risks and concerns about authentication of participants. For this reason, these protocol specifications need to describe security and authentication concerns that may be raised by the particular mechanisms defined and how those concerns may be addressed. 9. References 9.1. Normative References [ISO3166-1] "Codes for the representation of names of countries and their subdivisions -- Part 1: Country codes", ISO 3166-1, 2006. [M1400] "Designations for interconnections among operators' networks", ITU-T Recommendation M.1400, July 2006. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC5003] Metz, C., Martini, L., Balus, F., and J. Sugimoto, "Attachment Individual Identifier (AII) Types for Aggregation", RFC 5003, September 2007. [RFC6370] Bocci, M., Swallow, G., and E. Gray, "MPLS Transport Profile (MPLS-TP) Identifiers", RFC 6370, September 2011. [T.50] "International Reference Alphabet (IRA) (Formerly International Alphabet No. 5 or IA5) - Information technology - 7-bit coded character set for information exchange", ITU-T Recommendation T.50, September 1992. [Y.1731_cor1] "OAM functions and mechanisms for Ethernet based networks - Corrigendum 1", ITU-T Recommendation G.8013/Y.1731 Corrigendum 1, October 2011. Winter, et al. Standards Track [Page 11]
RFC 6923 MPLS-TP ITU-T IDs May 2013 9.2. Informative References [CC-list] "List of Country Codes - ISO 3166 (CCs)", <http://www.iso.org/iso/country_codes.htm>. [ICC-list] "List of ITU Carrier Codes (ICCs)", <http://www.itu.int/oth/T0201>. [RFC6371] Busi, I., Ed., and D. Allan, Ed., "Operations, Administration, and Maintenance Framework for MPLS- Based Transport Networks", RFC 6371, September 2011. Authors' Addresses Rolf Winter NEC EMail: rolf.winter@neclab.eu Eric Gray Ericsson EMail: eric.gray@ericsson.com Huub van Helvoort Huawei Technologies Co., Ltd. EMail: huub.van.helvoort@huawei.com Malcolm Betts ZTE EMail: malcolm.betts@zte.com.cn Winter, et al. Standards Track [Page 12]